基于动态负荷的冷热电联供系统优化研究

被引：11

作者：

宋祉慧 ^{[1
]}

林其钊 ^{[1
]}

刘涛 ^{[2
]}

刘燕菊 ^{[1
]}

姜雪丹 ^{[1
]}

机构：

[1] 中国科学技术大学热科学和能源工程系

[2] 西南科技大学计算机科学与技术学院

来源：

工程热物理学报 | 2020年 / 41卷 / 10期

关键词：

冷热电联供; 配置优化; 运行优化; 敏感性分析;

D O I：

暂无

中图分类号：

TK018 []; TU83 [空气调节、采暖、通风及其设备];

学科分类号：

081404 [供热、供燃气、通风及空调工程];

摘要：

本文以冷热电联供系统的设备特性和供需关系为基础,采用包括经济性、节能性和环保性在内的综合性能评价指标,建立了结构配置与运行策略的协同优化模型。以山西某工业园区冷热电联供系统为例,在MATLAB软件中求得系统最优配置和相应的运行策略,同时分析了以下因素对系统性能的影响:1)电价与天然气价;2)热需求与热产出比值。结果表明相较于传统分供系统,优化后的冷热电联供系统性能得到大幅度提升。

引用

页码：2372 / 2379

页数：8

共 14 条

[1]

Optimization and evaluation of CCHP systems considering incentive policies under different operation strategies.[J].Longxi Li;Shiwei Yu;Hailin Mu;Huanan Li.Energy.2018,

[2]

Analysis of inlet air throttling operation method for gas turbine in performance of CCHP system under different operation strategies.[J].Zefeng Wang;Wei Han;Na Zhang;Bosheng Su;Meng Liu;Hongguang Jin.Energy Conversion and Management.2018,

[3]

Multi-objective optimization of a gas turbine-based CCHP combined with solar and compressed air energy storage system.[J].Xusheng Wang;Cheng Yang;Manman Huang;Xiaoqian Ma.Energy Conversion and Management.2018,

[4]

A methodology to obtain the foremost type and optimal size of the prime mover of a CCHP system for a large-scale residential application.[J].M. Hossein Abbasi;Hoseyn Sayyaadi;Mohammad Tahmasbzadebaie.Applied Thermal Engineering.2018,

[5]

Optimal integration of renewable energy sources for autonomous tri-generation combined cooling; heating and power system based on evolutionary particle swarm optimization algorithm.[J].A. Lorestani;M.M. Ardehali.Energy.2018,

[6]

A MINLP multi-objective optimization model for operational planning of a case study CCHP system in urban China.[J].Xuyue Zheng;Guoce Wu;Yuwei Qiu;Xiangyan Zhan;Nilay Shah;Ning Li;Yingru Zhao.Applied Energy.2018,

[7]

Investigating the effects of load demands on selection of optimum CCHP-ORC plant.[J].Hassan Hajabdollahi.Applied Thermal Engineering.2015,

[8]

Optimization and analysis of CCHP system based on energy loads coupling of residential and office buildings.[J].Longxi Li;Hailin Mu;Weijun Gao;Miao Li.Applied Energy.2014,

[9]

Simultaneous use of MRM (maximum rectangle method) and optimization methods in determining nominal capacity of gas engines in CCHP (combined cooling; heating and power) systems.[J].Sepehr Sanaye;Navid Khakpaay.Energy.2014,

[10]

Optimum sizing and tracking of combined cooling heating and power systems for bulk energy consumers.[J].Saliya Jayasekara;Saman K. Halgamuge;Rahula A. Attalage;Rohitha Rajarathne.Applied Energy.2014,

← 1 2 →