Surface finishes from turning and facing with round nosed tools

被引：37

作者：

Childs, T. H. C. ^{[1
]}

Sekiya, K. ^{[2
]}

Tezuka, R. ^{[2
]}

Yamane, Y. ^{[2
]}

Dornfeld, D. ^{[3
]}

Lee, D. -E. ^{[3
]}

Min, S. ^{[3
]}

Wright, P. K. ^{[3
]}

机构：

[1] Univ Leeds, Sch Mech Engn, Leeds, W Yorkshire, England

[2] Hiroshima Univ, Grad Sch, Higashihiroshima 724, Japan

[3] Univ Calif Berkeley, Coll Engn, Berkeley, CA 94720 USA

来源：

CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2008年 / 57卷 / 01期

关键词：

precision; machining; surface roughness;

D O I：

10.1016/j.cirp.2008.03.121

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The range of surface roughnesses, and particularly the minimum roughnesses, achievable mainly with cemented carbide but also with single crystal diamond round nosed turning and facing inserts, has been experimentally studied, machining aluminium on engineering and precision lathes Insert edge sharpness and roughness measurements and characteristic variations with feed rate of machined surface profile are presented. When machine tool limits are avoided, R. values down to 0.02 times the insert edge radii have been obtained. (c) 2008 CIRP.

引用

页码：89 / 92

页数：4

共 17 条

[1] Characterisation of nanosurface generation in single-point diamond turning [J].

Cheung, CF ;

Lee, WB .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2001, 41 (06) :851-875

[2]

CHILDS THC, 2008, P 3 CIRP INT C HIGH

[3] A revised model for predicting surface roughness in turning [J].

Grzesik, W .

WEAR, 1996, 194 (1-2) :143-148

[4] Effect of plastic side flow on surface roughness in micro-turning process [J].

Liu, Kai ;

Melkote, Shreyes N. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (14) :1778-1785

[5] An analytical model for the prediction of minimum chip thickness in micromachining [J].

Liu, X. ;

DeVor, R. E. ;

Kapoor, S. G. .

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2006, 128 (02) :474-481

[6]

Lucca D.A., 1994, CIRP ANN-MANUF TECHN, V43, P43, DOI DOI 10.1016/S0007-8506(07)62160-X

[7]

MORIWAKI T, 1989, ANN CIRP, V38, P115, DOI DOI 10.1016/S0007-8506(07)62664-X

[8]

Okuda K, 2006, Progress of Machining Technology, Proceedings, P393

[9] Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel [J].

Özel, T ;

Hsu, TK ;

Zeren, E .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2005, 25 (3-4) :262-269

[10]

Petropoulos G. P., 1999, P 3 BALKANTRIB INT C, V1, P139

← 1 2 →