Mass-transfer characterization of metallic foams as supports for structured catalysts

被引:325
作者
Giani, L [1 ]
Groppi, G [1 ]
Tronconi, E [1 ]
机构
[1] Politecn Milan, Dipartimento Chim Mat & Ingn Chim G Natta, Ctr Excellenza Ingn Mat & Superfici Nanostruttura, I-20133 Milan, Italy
关键词
D O I
10.1021/ie0490886
中图分类号
TQ [化学工业];
学科分类号
0817 ;
摘要
Open-celled metal foams have been characterized as supports for structured catalysts, considering their utilization in gas-solid catalytic processes with short contact times and high reaction rates, typically controlled by gas-solid diffusional mass transport. Examples of such processes are found in the field of environmental catalysis, including, e.g., catalytic combustion, selective catalytic reduction (SCR-DeNOx), and automotive exhaust gas after treatment. In this work, foams with different cell sizes were coated with a thin layer of palladium-alumina and tested in a 9-mm inner diameter tubular reactor by performing the catalytic oxidation of CO at empty tube velocities in the range of 0.8-2.6 m/s. The coated foams exhibited sufficient catalytic activity to achieve mass-transfer-limited operation in the temperature range of 300-450 degrees C. Under such conditions, mass-transfer coefficients were determined according to a simple one-dimensional model of the test reactor. Adopting the average diameter of the foam struts as the characteristic length, we obtained a dimensionless correlation for the estimation of mass-transfer coefficients, which correlates all the data: it closely resembles semitheoretical literature correlations for heat transfer in flow across banks of tubes at low Reynolds numbers. Pressure drop measurements across foam samples were also collected for air velocities in the range of 1-16 m/s. The performances of foams, packed beds of pellets, and honeycomb monoliths as catalyst supports were compared on the basis of a dimensionless merit index, which accounts for the tradeoff between pressure drop and mass-transfer properties. Foams are largely superior to packed beds, because of their high voidage, but perform slightly worse than honeycomb monoliths. On the other hand, foams can afford marked reductions of reactor volume and weight, with respect to honeycombs, in fast, diffusion-controlled processes where pressure drop is of minor concern.
引用
收藏
页码:4993 / 5002
页数:10
相关论文
共 33 条
[1]   Numerical characterization of micro heat exchangers using experimentally tested porous aluminum layers [J].
Antohe, BV ;
Lage, JL ;
Price, DC ;
Weber, RM .
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 1996, 17 (06) :594-603
[2]  
Bejan A., 1993, Heat Transfer
[3]   Analysis of a catalytic annular reactor for very short contact times [J].
Beretta, A ;
Baiardi, P ;
Prina, D ;
Forzatti, P .
CHEMICAL ENGINEERING SCIENCE, 1999, 54 (06) :765-773
[4]   Thermophysical properties of high porosity metal foams [J].
Bhattacharya, A ;
Calmidi, VV ;
Mahajan, RL .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2002, 45 (05) :1017-1031
[5]   Simulations of flow through open cell metal foams using an idealized periodic cell structure [J].
Boomsma, K ;
Poulikakos, D ;
Ventikos, Y .
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 2003, 24 (06) :825-834
[6]   On the effective thermal conductivity of a three-dimensionally structured fluid-saturated metal foam [J].
Boomsma, K ;
Poulikakos, D .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2001, 44 (04) :827-836
[7]  
CAMPBELL LE, 1993, Patent No. 5256387
[8]  
Cristiani C, 1998, STUD SURF SCI CATAL, V118, P119
[9]   PRESSURE-DROP PREDICTION FOR FLOW-THROUGH HIGH-POROSITY METALLIC FOAMS [J].
DUPLESSIS, P ;
MONTILLET, A ;
COMITI, J ;
LEGRAND, J .
CHEMICAL ENGINEERING SCIENCE, 1994, 49 (21) :3545-3553
[10]  
Forchheimer P., 1901, Zeitschrift des Vereines Deutscher Ingenieure, V45, P1782