Deformation behavior of Zr65Al10Ni10Cu15 glassy alloy with wide supercooled liquid region

被引:171
作者
Kawamura, Y
Shibata, T
Inoue, A
Masumoto, T
机构
[1] Institute for Materials Research, Tohoku University
关键词
D O I
10.1063/1.117413
中图分类号
O59 [应用物理学];
学科分类号
摘要
We report the stress-strain behavior for a Zr65Al10Ni10Cu15 (at.%) glassy alloy with a significant supercooled liquid region of 105 K. the transition temperature from inhomogeneous deformation to a homogeneous one increases with increasing strain rate. The alloy in the supercooled liquid state, however, exhibited the homogeneous deformation even at higher rates above 0.5 s(-1). The strength was also dependent on the strain rate and independent of temperature in the inhomogeneous deformation region, and was sensitive to both strain rate and temperature in the homogeneous region. The stress-strain curves in the homogeneous deformation mode were accompanied by a stress overshoot and its height increases with increasing temperature and strain rate. (C) 1996 American Institute of Physics.
引用
收藏
页码:1208 / 1210
页数:3
相关论文
共 18 条
[1]   PLASTIC-DEFORMATION IN METALLIC GLASSES [J].
ARGON, AS .
ACTA METALLURGICA, 1979, 27 (01) :47-58
[3]   PREPARATION OF BULKY AMORPHOUS ZR-AL-CO-NI-CU ALLOYS BY COPPER MOLD CASTING AND THEIR THERMAL AND MECHANICAL-PROPERTIES [J].
INOUE, A ;
ZHANG, T ;
MASUMOTO, T .
MATERIALS TRANSACTIONS JIM, 1995, 36 (03) :391-398
[4]   MG-CU-Y BULK AMORPHOUS-ALLOYS WITH HIGH-TENSILE STRENGTH PRODUCED BY A HIGH-PRESSURE DIE-CASTING METHOD [J].
INOUE, A ;
NAKAMURA, T ;
NISHIYAMA, N ;
MASUMOTO, T .
MATERIALS TRANSACTIONS JIM, 1992, 33 (10) :937-945
[5]   PRODUCTION OF AMORPHOUS CYLINDER AND SHEET OF LA55AL25NI20 ALLOY BY A METALLIC MOLD CASTING METHOD [J].
INOUE, A ;
ZHANG, T ;
MASUMOTO, T .
MATERIALS TRANSACTIONS JIM, 1990, 31 (05) :425-428
[6]   FULL STRENGTH COMPACTS BY EXTRUSION OF GLASSY METAL-POWDER AT THE SUPERCOOLED LIQUID-STATE [J].
KAWAMURA, Y ;
KATO, H ;
INOUE, A ;
MASUMOTO, T .
APPLIED PHYSICS LETTERS, 1995, 67 (14) :2008-2010
[7]   PREPARATION OF BULK AMORPHOUS-ALLOYS BY HIGH-TEMPERATURE SINTERING UNDER A HIGH-PRESSURE [J].
KAWAMURA, Y ;
TAKAGI, M ;
SENOO, M ;
IMURA, T .
MATERIALS SCIENCE AND ENGINEERING, 1988, 98 :415-418
[8]   A NEWLY DEVELOPED WARM EXTRUSION TECHNIQUE FOR COMPACTING AMORPHOUS ALLOY POWDERS [J].
KAWAMURA, Y ;
TAKAGI, M ;
AKAI, M ;
IMURA, T .
MATERIALS SCIENCE AND ENGINEERING, 1988, 98 :449-452
[9]  
KAWAMURA Y, 1991, J JPN SOC POWDER POW, V38, P110
[10]  
LI JCM, 1993, RAPIDLY SOLIDIFIED A, P379