Corrosion Behaviour of Selective Laser Melted Ti-TiB Biocomposite in Simulated Body Fluid

被引：181

作者：

Chen, Yang ^{[1
]}

Zhang, Junxi ^{[1
]}

Dai, Nianwei ^{[1
]}

Qin, Peng ^{[2
]}

Attar, Hooyar ^{[2
]}

Zhang, Lai-Chang ^{[2
]}

机构：

[1] Shanghai Univ Elect Power, Shanghai Key Lab Mat Protect & Adv Mat Elect Powe, Shanghai 200090, Peoples R China

[2] Edith Cowan Univ, Sch Engn, 270 Joondalup Dr, Perth, WA 6027, Australia

来源：

ELECTROCHIMICA ACTA | 2017年 / 232卷

基金：

澳大利亚研究理事会;

关键词：

Titanium biocomposite; Selective laser melting; Corrosion resistance; Passive film; COMMERCIALLY PURE TITANIUM; MECHANICAL-PROPERTIES; TI-6AL-4V ALLOY; GALVANIC CORROSION; MATRIX COMPOSITES; AL-12SI ALLOY; DEGREES-C; MICROSTRUCTURE; RESISTANCE; WEAR;

D O I：

10.1016/j.electacta.2017.02.112

中图分类号：

O646 [电化学、电解、磁化学];

学科分类号：

070208 [无线电物理];

摘要：

The corrosion behaviour of CP-Ti and Ti-TiB composite produced by selective laser melting (SLM) in the artificial simulated body fluid (Hank's solution) at body temperature was investigated systematically by using electrochemical measurements (potentiodynamic polarisation curves and electrochemical impedance spectroscopy), together with some detailed structural characterisations. The results demonstrate that SLM-produced Ti-TiB composite samples possess better corrosion resistance than SLM-produced CP-Ti samples in Hank's solution. Due to these tiny TiB and TiB2 particles acting as the micro-cathode uniformly distributing in titanium matrix, anodic dissolution of titanium matrix in the corrosion process is prominently facilitated in early stages, followed by rapid passivation on the surface. The corrosion mechanism of Ti-TiB composite samples has also been discussed in detail in this paper. (C) 2017 Elsevier Ltd. All rights reserved.

引用

收藏

页码：89 / 97

页数：9

相关论文

共 55 条

[1]

Do 'passive' medical titanium surfaces deteriorate in service in the absence of wear? [J].

Addison, O. ;

Davenport, A. J. ;

Newport, R. J. ;

Kalra, S. ;

Monir, M. ;

Mosselmans, J. F. W. ;

Proops, D. ;

Martin, R. A. .

JOURNAL OF THE ROYAL SOCIETY INTERFACE, 2012, 9 (76) :3161-3164

[2]

In situ impedance spectroscopy study of the electrochemical corrosion of Ti and Ti-6Al-4V in simulated body fluid at 25 °C and 37 °C [J].

Alves, V. A. ;

Reis, R. Q. ;

Santos, I. C. B. ;

Souza, D. G. ;

Goncalves, T. de F. ;

Pereira-da-Silva, M. A. ;

Rossi, A. ;

da Silva, L. A. .

CORROSION SCIENCE, 2009, 51 (10) :2473-2482

[3]

Electrochemical characterisation of aluminium AA7075-T6 and solution heat treated AA7075 using a micro-capillary cell [J].

Andreatta, F ;

Lohrengel, MM ;

Terryn, H ;

de Wit, JHW .

ELECTROCHIMICA ACTA, 2003, 48 (20-22) :3239-3247

[4]

Galvanic corrosion of aircraft bonded joints as a result of adhesive microcracks [J].

Anes, V. ;

Pedro, R. S. ;

Henriques, E. ;

Freitas, M. ;

Reis, L. .

XV PORTUGUESE CONFERENCE ON FRACTURE, PCF 2016, 2016, 1 :218-225

[5]

Corrosion behaviour of investment cast and friction stir processed Ti-6Al-4V [J].

Atapour, M. ;

Pilchak, A. ;

Frankel, G. S. ;

Williams, J. C. .

CORROSION SCIENCE, 2010, 52 (09) :3062-3069

[6]

Comparison of wear properties of commercially pure titanium prepared by selective laser melting and casting processes [J].

Attar, H. ;

Prashanth, K. G. ;

Chaubey, A. K. ;

Calin, M. ;

Zhang, L. C. ;

Scudino, S. ;

Eckert, J. .

MATERIALS LETTERS, 2015, 142 :38-41

[7]

Mechanical behavior of porous commercially pure Ti and Ti-TiB composite materials manufactured by selective laser melting [J].

Attar, H. ;

Loeber, L. ;

Funk, A. ;

Calin, M. ;

Zhang, L. C. ;

Prashanth, K. G. ;

Scudino, S. ;

Zhang, Y. S. ;

Eckert, J. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 625 :350-356

[8]

Comparative study of microstructures and mechanical properties of in situ Ti-TiB composites produced by selective laser melting, powder metallurgy, and casting technologies [J].

Attar, H. ;

Boenisch, M. ;

Calin, M. ;

Zhang, L. C. ;

Zhuravleva, K. ;

Funk, A. ;

Scudino, S. ;

Yang, C. ;

Eckert, J. .

JOURNAL OF MATERIALS RESEARCH, 2014, 29 (17) :1941-1950

[9]

Manufacture by selective laser melting and mechanical behavior of commercially pure titanium [J].

Attar, H. ;

Calin, M. ;

Zhang, L. C. ;

Scudino, S. ;

Eckert, J. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 593 :170-177

[10]

Effect of Powder Particle Shape on the Properties of In Situ Ti-TiB Composite Materials Produced by Selective Laser Melting [J].

Attar, Hooyar ;

Prashanth, Konda G. ;

Zhang, Lai-Chang ;

Calin, Mariana ;

Okulov, Ilya V. ;

Scudino, Sergio ;

Yang, Chao ;

Eckert, Juergen .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2015, 31 (10) :1001-1005

← 1 2 3 4 5 6 →