The development of superplastic ductilities and microstructural homogeneity in a magnesium ZK60 alloy processed by ECAP

被引：118

作者：

Figueiredo, Roberto B.

Langdon, Terence G. ^{[1
]}

机构：

[1] Univ So Calif, Dept Aerosp & Mech Engn, Los Angeles, CA 90089 USA

[2] Univ So Calif, Dept Mat Sci, Los Angeles, CA 90089 USA

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2006年 / 430卷 / 1-2期

基金：

美国国家科学基金会;

关键词：

equal-channel angular pressing (ECAP); homogeneity; magnesium alloys; severe plastic deformation; superplasticity;

D O I：

10.1016/j.msea.2006.05.056

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

An extruded ZK60 magnesium alloy was processed by equal-channel angular pressing (ECAP) and then tested in tension at elevated temperatures. The results show the alloy is, superplastic at a testing temperature of 473 K with an optimum ductility of similar to 1310% when using an initial strain rate of 2.0 x 10(-4) s(-1). The results demonstrate that optimum superplasticity is achieved at intermediate strain rates and there are decreases in the elongations to failure at both faster and slower strain rates. Microhardness measurements were taken both on the cross-sectional plane and along the axial direction after processing by ECAP. These measurements show the alloy is essentially homogeneous in the as-pressed condition. (c) 2006 Elsevier B.V. All rights reserved.

引用

页码：151 / 156

页数：6

共 35 条

[1] Influence of pressing speed on microstructural development in equal-channel angular pressing [J].

Berbon, PB ;

Furukawa, M ;

Horita, Z ;

Nemoto, M ;

Langdon, TG .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1999, 30 (08) :1989-1997

[2] Analysis of the billet deformation behaviour in equal channel angular extrusion [J].

Bowen, JR ;

Gholinia, A ;

Roberts, SM ;

Prangnell, PB .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 287 (01) :87-99

[3] Superplasticity and internal friction in microcrystalline AZ91 and ZK60 magnesium alloys processed by equal-channel angular pressing [J].

Chuvil'deev, V ;

Nieh, TG ;

Gryaznov, MY ;

Kopylov, VI ;

Sysoev, AN .

JOURNAL OF ALLOYS AND COMPOUNDS, 2004, 378 (1-2) :253-257

[4] Low-temperature superplasticity and internal friction in microcrystalline Mg alloys processed by ECAP [J].

Chuvil'deev, VN ;

Nieh, TG ;

Gryaznov, MY ;

Sysoev, AN ;

Kopylov, VI .

SCRIPTA MATERIALIA, 2004, 50 (06) :861-865

[5] Hot working of Ti-6Al-4V via equal channel angular extrusion [J].

DeLo, DP ;

Semiatin, SL .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1999, 30 (09) :2473-2481

[6]

Estrin Y, 2004, ULTRAFINE GRAINED MATERIALS III, P247

[7] Improving the superplastic properties of a two-phase Mg-8% Li alloy through processing by ECAP [J].

Furui, M ;

Xu, C ;

Aida, T ;

Inoue, M ;

Anada, H ;

Langdon, TG .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 410 :439-442

[8] The shearing characteristics associated with equal-channel angular pressing [J].

Furukawa, M ;

Iwahashi, Y ;

Horita, Z ;

Nemoto, M ;

Langdon, TG .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 257 (02) :328-332

[9]

HILPERT M, 1998, MAGNESIUM ALLOYS THE, P319

[10] A two-step processing route for achieving a superplastic forming capability in dilute magnesium alloys [J].

Horita, Z ;

Matsubara, K ;

Makii, K ;

Langdon, TG .

SCRIPTA MATERIALIA, 2002, 47 (04) :255-260

← 1 2 3 4 →