Tear-off wear mechanism of sintered diamond tool in cutting SiC-particle-strengthened epoxy composites

被引：6

作者：

Afaghani, JED ^{[1
]}

Yamaguchi, K ^{[1
]}

Nakamoto, T ^{[1
]}

Yoshino, K ^{[1
]}

机构：

[1] NAGOYA UNIV, DEPT MECH ENGN, CHIKUSA KU, NAGOYA, AICHI 464, JAPAN

来源：

WEAR | 1997年 / 206卷 / 1-2期

关键词：

dispersion-strengthened composite; plastic composite; silicon carbide particle; sintered diamond tool; cutting; tool wear; tear-off mechanism;

D O I：

10.1016/S0043-1648(96)07458-3

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This study concerns the wear of sintered diamond tools in the cutting of SiC-particle-epoxy composites. The effects of the SiC particle size, volume ratio in the composite and diamond grain size of the cutting tool on tool wear were investigated. The experimental work has shown that a coarse-grained diamond tool exhibits higher wear resistance than a corresponding fine-grained tool. Greater tool wear was obtained in cutting the composites that had coarser particles and a higher volume ratio of SiC. Moreover, it was found that the tool wear increases drastically when the SiC particles are larger than the tool grains. A wear model of the tool was proposed, in which the tool is worn mainly by the 'tear-off' mechanism of the diamond grains. This model could explain the experimental results by comparing the pushing force of an SiC particle with the tear-off resistance of the diamond grains of the tool. Finally, a fatigue-like empirical curve was established. This curve can be used to predict the wear of the tool during cutting of the composite. (C) 1997 Elsevier Science S.A.

引用

页码：221 / 229

页数：9

共 30 条

[1] Whisker behaviors and tool wear in cutting of unidirectional SiC whisker-reinforced plastic [J].

Afaghani, JED ;

Yamaguchi, K ;

Horaguchi, I ;

Nakamoto, T .

WEAR, 1996, 195 (1-2) :223-231

[2]

AFAGHANI JED, 1994, JSPE PUBL SER, P407

[3]

AFAGHANI JED, 1993, P IMMM 93 TSU JAPAN, P273

[4]

AFAGHANI JED, 1995, P IMMM 95 BEIJING, P455

[5]

[Anonymous], 1992, COMPOS MANUF, DOI DOI 10.1016/0956-7143(92)90119-F

[6]

Asahina K., 1991, J JPN SOC PRECISION, V57, P2187

[7] ON THE MACHINING OF FIBER-REINFORCED PLASTIC (FRP) COMPOSITE LAMINATES [J].

BHATNAGAR, N ;

RAMAKRISHNAN, N ;

NAIK, NK ;

KOMANDURI, R .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 1995, 35 (05) :701-716

[8]

HASEGAWA Y, 1984, J JPN SOC PRECISON E, V50, P1747

[9]

Hocheng H, 1993, Compos Manuf, V4, P103, DOI [10.1016/0956-7143(93)90077-L, DOI 10.1016/0956-7143(93)90077-L]

[10]

Inoue H., 1994, Journal of the Society of Materials Science, Japan, V43, P451, DOI 10.2472/jsms.43.451

← 1 2 3 →