Workload planning in small lot printed circuit board assembly

被引：11

作者：

Günther H.-O. ^{[1
]}

Grunow M. ^{[1
]}

Schorling C. ^{[1
]}

机构：

[1] Department of Industrial Management, Technical University of Berlin, D-10585 Berlin, Wilmersdorfer Strasse 148

来源：

Operations-Research-Spektrum | 1997年 / 19卷 / 2期

关键词：

Aggregational error; Decision support; Linear programming; Modelling; Printed circuit board assembly; Production; Scheduling;

D O I：

10.1007/BF01545517

中图分类号：

学科分类号：

摘要：

The problem of workload planning in small lot printed circuit board (PCB) assembly concerns the determination of the daily mix of production orders to be released into the production system. When switching from one production order (board type) to another, a considerable set-up time is incurred based on the number of component feeders to be replaced in the component magazine of the assembly machines. To support the order-mix decision faced by a major electronics manufacturer, two versions of a linear programming model are developed. The models differ primarily in their degree of aggregation and their computational effort. In order to reduce the aggregational error incurred, a fuzzy approach is developed to estimate the number of component set-ups at automatic SMD placement machines. Our numerical investigation reveals that sufficiently accurate solutions may be obtained from a highly aggregate fuzzy LP-model and this is achieved with considerably less computational effort than with a more detailed LP-model. We also demonstrate the potential suitability of the fuzzy LP-model for implementation within an interactive decision support system. © Springer-Verlag 1997.

引用

页码：147 / 157

页数：10

共 27 条

[1]

Ahmadi R.H., Kouvelis P., Staging problem of a dual delivery pick-and-place machine in printed circuit card assembly, Oper Res, 42, pp. 81-91, (1994)

[2]

Askin R.G., Dror M., Vakharia A.J., Printed circuit board family grouping and component allocation for a multimachine, open-shop assembly cell, Nav Res Log, 41, pp. 587-608, (1994)

[3]

Ball M.O., Magazine M.J., Sequencing of insertions in printed circuit board assembly, Oper Res, 36, pp. 192-201, (1988)

[4]

Bard J.F., Clayton R.W., Feo T.A., Machine setup and component placement in printed circuit board assembly, Int J Flex Manuf Syst, 6, pp. 5-31, (1994)

[5]

Crama Y., Kolen A.W.J., Oerlemans A.G., Spieksma F.C.R., Throughput rate optimization in the automated assembly of printed circuit boards, Ann Opers Res, 26, pp. 455-480, (1990)

[6]

Crama Y., Kolen A.W.J., Oerlemans A.G., Spieksma F.C.R., Minimizing the number of tool switches on a flexible machine, Int J Flex Manuf Syst, 6, pp. 33-54, (1994)

[7]

Deane R.H., Moon S.H., Work flow control in the flexible flow line, Int J Flex Manuf Syst, 3, 4, pp. 217-235, (1992)

[8]

Grunow M., Gunther H.O., Gronalt M., Zeller R., A heuristic for component switching on SMD placement machines, Discussion Paper, (1996)

[9]

Gunther H.O., Gronalt M., Piller F., Computergestützte Simulation eines hochautomatisierten Montagesystems, Management & Computer, 2, pp. 25-32, (1994)

[10]

Gunther H.O., Gronalt M., Piller F., A linear programming model for workload planning in printed circuit board assembly, Operations Research Proceedings 1994, pp. 312-317, (1995)

← 1 2 3 →