THE LINEAR APPROXIMATED EQUATION OF VIBRATION OF A PAIR OF SPUR GEARS (THEORY AND EXPERIMENT)

被引:93
作者
CAI, Y
HAYASHI, T
机构
[1] Precision and Intelligence Laboratory, Research Laboratory of Precision Machinery and Electronics, Tokyo Institute of Technology, Yokohama, 227, 4259 Nagatsuta, Midori-ku
关键词
D O I
10.1115/1.2919414
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
The nonlinear equation for the rotational vibration of a pair of spur gears has a restriction that the analytical solution of the equation cannot be obtained. In this paper, the linear equation of vibration is derived theoretically and its physical model, i.e., the linear model of vibration is presented. The analytical solution of the linear equation, which is derived by analytical method, agrees well with the numerically calculated result by the nonlinear equation. By analyzing the analytical solution of the linear equation in detail, we clarified the relation between the waveforms of the vibration and the profile error of gear pairs, and also found that the effect of the contact ratio to the vibration is large and complex. The equivalent error, accounting for effects of the static load, the time- varying stiffness, and the profile error of gear pairs, is proposed in this paper. It can be considered as promising for evaluating the profile error, because the vibration of gear pairs is excited mainly by the equivalent error. Finally, for confirming the above results, the vibration of two tested gear pairs has been measured by an experimental set-up for this purpose.
引用
收藏
页码:558 / 570
页数:13
相关论文
共 10 条
[1]  
Cai Y.R., Hayashi T., The Linear Approximated Equation of Vibration of a Pair of Spur Gears (Theoretical Analysis and Experiment), Proceedings of the International Conference on Motion and Power Transmissions, pp. 21-26, (1991)
[2]  
Cai Y.R., Hayashi T., The Rotational Vibration of Spur Gears Due to Tooth Profile Error (In Japanese), Journal of the Japan Society of Precision Engineering, 56, 1, pp. 121-127, (1990)
[3]  
Cai Y.R., Hayashi T., Estimation of Vibration of a Spur Gear Pair Due to Relative Tooth Profile Error (In Japanese), Journal of the Japan Society of Precision Engineering, 56, 8, pp. 1424-1430, (1990)
[4]  
Cai Y.R., Hayashi T., The Optimum Modification of Tooth Profile of Power Transmission Spur Gears to Make the Rotational Vibration Equal Zero (In Japanese), Transactions of the Japan Society of Mechanical Engineers, 57, 544, pp. 3957-3963, (1991)
[5]  
Hayashi T., Hayashi I., The Rotational Vibration of a Spur Gear with Tooth Profile Error, Bulletin of Research Laboratory of Precision Machinery and Electronics, Tokyo Institute of Technology, 38, pp. 35-42, (1976)
[6]  
Kasuba R., Evans J., An Extended Model for Determining Dynamic Loads in Spur Gearing, ASME Journal of Mechanical Design, 103, pp. 398-409, (1981)
[7]  
Kubo A., Kiyono S., Study of the Load Transmission Performance of Cylindrical Gears (4th Reports, In Japanese), Transactions of the Japan Society of Mechanical Engineers, 46, 401, pp. 86-98, (1980)
[8]  
Lin H.H., Huston R.L., Coy J.J., On Dynamic Loads in Parallel Shaft Transmissions: Part 1-Modeling and Analysis, ASME Journal of Mechanisms, Transmissions, and Automation in Desion, 110, pp. 221-225, (1988)
[9]  
Lin H.H., Huston R.L., Coy J.J., On Dynamic Loads in Parallel Shaft Transmissions: Part 2-Parameter Study, ASME Journal of Mechanisms, Transmissions, and Automation in Design, 110, pp. 226-229, (1988)
[10]  
Sato T., Vibration of Power Transmission Spur Gears (In Japanese), Ph.D. Dissertation, Tokyo Institute of Technology, Supervised by Prof. K. Umezawa, (1982)