Evaluation of the parameters related to glass-forming ability of bulk metallic glasses

被引：28

作者：

Cai, AH ^{[1
]}

Sun, GX ^{[1
]}

Pan, Y ^{[1
]}

机构：

[1] Southeast Univ, Dept Mat Sci & Engn, Nanjing 210096, Peoples R China

来源：

MATERIALS & DESIGN | 2006年 / 27卷 / 06期

关键词：

difference in atomic size ratios; difference in atomic electronegativity ratios; tonicity index; bulk metallic glasses; glass-forming ability; weighted averages principle;

D O I：

10.1016/j.matdes.2004.11.015

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Some parameters of the alloys, such as S-mix, T-m, Delta H-m, Delta d, Delta e and nu are calculated by using the weighted averages principle. The correlation coefficients between the related parameters and R-c, T-rg and Delta T-x are calculated based on the statistics. In particular, the relationships between three related parameters, i.e., Delta d, Delta e and nu, and R-c are researched, respectively. The results are shown: S-mix, T-m and Delta H-m all are advantageous of the increase of the glass-forming ability (GFA) of the alloy. Delta T-x is better than T-rg for describing the GFA of the alloy from the point of statistics view, but two parameters are not suitable for the description of the GFA. The optimum phenomena are found in the relationships between R-c and three parameters, such as Delta d, Delta e and nu, respectively. Based on the above-mentioned results, in order to enhance the GFA of the alloy, the match among the atomic percentage, Delta d, Delta e and nu must be harmonious. The optimum composition of the components in the alloy and optimum atomic percentage of additives may be related to the relations related above. (C) 2004 Elsevier Ltd. All rights reserved.

引用

页码：479 / 488

页数：10

共 35 条

[11] HIGH-STRENGTH BULK AMORPHOUS-ALLOYS WITH LOW CRITICAL COOLING RATES [J].

INOUE, A .

MATERIALS TRANSACTIONS JIM, 1995, 36 (07) :866-875

[12] PREPARATION OF 16 MM DIAMETER ROD OF AMORPHOUS ZR65AL7.5NI10CU17.5 ALLOY [J].

INOUE, A ;

ZHANG, T ;

NISHIYAMA, N ;

OHBA, K ;

MASUMOTO, T .

MATERIALS TRANSACTIONS JIM, 1993, 34 (12) :1234-1237

[13] Fabrication of bulk glassy Zr55Al10Ni5Cu30 alloy of 30 mm in diameter by a suction casting methodQ [J].

Inoue, A ;

Zhang, T .

MATERIALS TRANSACTIONS JIM, 1996, 37 (02) :185-187

[14] PRODUCTION OF AMORPHOUS CYLINDER AND SHEET OF LA55AL25NI20 ALLOY BY A METALLIC MOLD CASTING METHOD [J].

INOUE, A ;

ZHANG, T ;

MASUMOTO, T .

MATERIALS TRANSACTIONS JIM, 1990, 31 (05) :425-428

[15]

INOUE A, 1991, MAT T JIM, V32, P1005

[16] Estimation of the glass transition temperature in metallic glasses [J].

Jiang, HG ;

Baram, J .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1996, 208 (02) :232-238

[17]

JIN SS, 1980, BASE APPL QUANTA CHE

[18] Spark welding of Zr55Al10Ni5Cu30 bulk metallic glasses [J].

Kawamura, Y ;

Ohno, Y .

SCRIPTA MATERIALIA, 2001, 45 (02) :127-132

[19] Glass forming ability of bulk glass forming alloys [J].

Li, Y ;

Ng, SC ;

Ong, CK ;

Hng, HH ;

Goh, TT .

SCRIPTA MATERIALIA, 1997, 36 (07) :783-787

[20]

LI Y, 1995, J HUAZHONG U SCI TEC, V23, P65

← 1 2 3 4 →