Mechanical properties of nanocrystalline materials

被引:3777
作者
Meyers, MA [1 ]
Mishra, A [1 ]
Benson, DJ [1 ]
机构
[1] Univ Calif San Diego, Dept Mech & Aerosp Engn, Mat Sci & Engn Program, La Jolla, CA 92093 USA
基金
美国国家科学基金会;
关键词
D O I
10.1016/j.pmatsci.2005.08.003
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The mechanical properties of nanocrystalline materials are reviewed, with emphasis on their constitutive response and on the fundamental physical mechanisms. In a brief introduction, the most important synthesis methods are presented. A number of aspects of mechanical behavior are discussed, including the deviation from the Hall-Petch slope and possible negative slope, the effect of porosity, the difference between tensile and compressive strength, the limited ductility, the tendency for shear localization, the fatigue and creep responses. The strain-rate sensitivity of FCC metals is increased due to the decrease in activation volume in the nanocrystalline regime; for BCC metals this trend is not observed, since the activation volume is already low in the conventional polycrystalline regime. In fatigue, it seems that the S-N curves show improvement due to the increase in strength, whereas the da/dN curve shows increased growth velocity (possibly due to the smoother fracture requiring less energy to propagate). The creep results are conflicting: while some results indicate a decreased creep resistance consistent with the small grain size, other experimental results show that the creep resistance is not negatively affected. Several mechanisms that quantitatively predict the strength of nanocrystalline metals in terms of basic defects (dislocations, stacking faults, etc.) are discussed: break-up of dislocation pile-ups, core-and-mantle, grain-boundary sliding, grain-boundary dislocation emission and annihilation, grain coalescence, and gradient approach. Although this classification is broad, it incorporates the major mechanisms proposed to this date. The increased tendency for twinning, a direct consequence of the increased separation between partial dislocations, is discussed. The fracture of nanocrystalline metals consists of a mixture of ductile dimples and shear regions; the dimple size, while much smaller than that of conventional polycrystalline metals, is several times larger than the grain size. The shear regions are a direct consequence of the increased tendency of the nanocrystalline metals to undergo shear localization. The major computational approaches to the modeling of the mechanical processes in nanocrystalline metals are reviewed with emphasis on molecular dynamics simulations, which are revealing the emission of partial dislocations at grain boundaries and their annihilation after crossing them. (c) 2005 Published by Elsevier Ltd.
引用
收藏
页码:427 / 556
页数:130
相关论文
共 355 条
[51]   Nanocrystalline electrodeposited Ni: microstructure and tensile properties [J].
Dalla Torre, F ;
Van Swygenhoven, H ;
Victoria, M .
ACTA MATERIALIA, 2002, 50 (15) :3957-3970
[52]   Nanocrystalline ceramics from sucrose process [J].
Das, RN .
MATERIALS LETTERS, 2001, 47 (06) :344-350
[53]   Chemical synthesis of nanocrystalline lead zirconate-titanate powders using tartarate precursor [J].
Das, RN ;
Pramanik, P .
MATERIALS LETTERS, 1999, 40 (06) :251-254
[54]   STRESS DEPENDENCE OF CREEP IN NANOCRYSTALLINE NI-P ALLOY [J].
DENG, J ;
WANG, DL ;
KONG, QP ;
SHUI, JP .
SCRIPTA METALLURGICA ET MATERIALIA, 1995, 32 (03) :349-352
[55]   Atomistic simulations as guidance to experiments [J].
Derlet, PM ;
Hasnaoui, A ;
Van Swygenhoven, H .
SCRIPTA MATERIALIA, 2003, 49 (07) :629-635
[56]   Length scale effects in the simulation of deformation properties of nanocrystalline metals [J].
Derlet, PM ;
Van Swygenhoven, H .
SCRIPTA MATERIALIA, 2002, 47 (11) :719-724
[57]   Synthesis of nanocrystalline TiO2 at 100 °C [J].
Dhage, SR ;
Choube, VD ;
Samuel, V ;
Ravi, V .
MATERIALS LETTERS, 2004, 58 (17-18) :2310-2313
[58]   Co-precipitation technique for the preparation of nanocrystalline ferroelectric SrBi2Ta2O9 [J].
Dhage, SR ;
Khollam, YB ;
Deshpande, SB ;
Ravi, V .
MATERIALS RESEARCH BULLETIN, 2003, 38 (11-12) :1601-1605
[59]   Grain size dependence of the fatigue behaviour of a ultrafine-grained AISI 304 stainless steel [J].
Di Schino, A ;
Kenny, JM .
MATERIALS LETTERS, 2003, 57 (21) :3182-3185
[60]  
DIEHL J, 1956, Z METALLKD, V47, P331