Mechano-chemical activation synthesis (MCAS) of disordered Mg(BH4)2 using NaBH4

被引:27
作者
Varin, R. A. [1 ]
Chiu, Ch. [1 ]
Wronski, Z. S. [1 ,2 ]
机构
[1] Univ Waterloo, Dept Mech Engn, Waterloo, ON N2L 3G1, Canada
[2] Nat Resources Canada, CANMET Energy Technol Ctr, Hydrogen Fuel Cells & Transportat, Ottawa, ON K1A 1M1, Canada
基金
加拿大自然科学与工程研究理事会;
关键词
hydrogen storage materials; magnesium borohydride; sodium borohydride; mechano-chemical activation synthesis; X-ray diffraction; differential scanning calorimetry;
D O I
10.1016/j.jallcom.2007.07.110
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Mechano-chemical activation synthesis (MCAS) of a powder mixture ratio 2NaBH(4) and MgCl2 was carried out by ball milling in a magneto-mill from 1 to 100 h duration with the objective of initiating a metathesis reaction 2NaBH(4) +MgCl2 -> Mg(BH4)(2) + 2NaCl. It is found from X-ray diffraction (XRD) that the reaction has been only partially completed resulting in the formation of NaCl and a (Na,Mg)BH4 solid solution. The solutionizing effect of Mg becomes more intense as milling time increases. No XRD peaks of crystalline Mg(BH4)2 are observed. Although the result of XRD analysis in the present work does not indicate the presence of a crystalline Mg(BH4)2 hydride, the similarity of thermal events in the DSC test of the milled powder mixtures to those of crystalline Mg(BH4)(2) [D.S. Stasinevich, G.A. Egorenko, Russ. J. Inorg. Chem. 13 (1968) 341-343; V.N. Konoplev, V.M. Bakulina, Izv. Akad. Nauk SSSR 1 (1971) 159-161] indicates the possibility of presence of a "disordered" Mg(BH4)2 in the in the milled powder mixture, as specifically proposed by Nakamori et al. [Y. Nakamori, K. Miwa, A. Ninomiya, H. Li, N. Ohba, S-I. Towata, A. Zuttel, S-I. Orimo, Phys. Rev. B74 (2006) 045126; Y. Nakamori, H.-W. Li, K. Kikuchi, M. Aoki, K. Miwa, S. Towata, S. Orimo, J. Alloys Compd., in press, doi: 10. 1016/j.jallcom.2007.03.144]. It is hypothesized that the presence of (Na,Mg)BH4 solid solution in the MCAS process inhibits the formation of crystalline Mg(BH4)(2). Regardless of the nature of the synthesized hydride phase the milled powders desorb hydrogen within the 275-420 degrees C temperature range and the total amount of hydrogen desorbed gradually decreases with increasing milling time reaching similar to 2.1 wt.% for the powder milled for 100 h. However, regardless of the milling time the total amount of hydrogen desorbed within 275-420 degrees C is always less than the theoretical hydrogen capacity in the initial mixture of 2NaBH(4) and NlgCl(2) (similar to 4.7 wt.%). (C) 2007 Elsevier B.V. All rights reserved.
引用
收藏
页码:201 / 208
页数:8
相关论文
共 30 条
[1]  
[Anonymous], CRC HDB CHEM PHYS
[2]  
ASKELAND DR, 2003, SCI ENG MAT, P980
[3]   UNIVERSAL HIGH-PERFORMANCE BALL-MILLING DEVICE AND ITS APPLICATION FOR MECHANICAL ALLOYING [J].
CALKA, A ;
RADLINSKI, AP .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1991, 134 :1350-1353
[4]  
CALKA RA, 2001, P INT S PROC FABR AD, P263
[5]   Solid-phase solvate-free formation of magnesium hydroaluminates Mg(AlH4)2 and MgAlH5 upon mechanochemical activation or heating of magnesium hydride and aluminum chloride mixtures [J].
Dymova, TN ;
Mal'tseva, NN ;
Konoplev, VN ;
Golovanova, AI ;
Aleksandrov, DP ;
Sizareva, AS .
RUSSIAN JOURNAL OF COORDINATION CHEMISTRY, 2003, 29 (06) :385-389
[6]  
Dymova TN, 1999, RUSS J COORD CHEM+, V25, P312
[7]   Nanotechnological aspects in materials for hydrogen storage [J].
Fichtner, M .
ADVANCED ENGINEERING MATERIALS, 2005, 7 (06) :443-455
[8]   Mechanically alloyed metal hydride systems [J].
Huot, J ;
Liang, G ;
Schulz, R .
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING, 2001, 72 (02) :187-195
[9]   Mechanochemical synthesis and thermal decomposition of zinc borohydride [J].
Jeon, Eun ;
Cho, YoungWhan .
JOURNAL OF ALLOYS AND COMPOUNDS, 2006, 422 (1-2) :273-275
[10]   Mechanochemical synthesis and thermal decomposition of Mg(AlH4)2 [J].
Kim, Yoonyoung ;
Lee, Eung-Kyu ;
Shim, Jae-Hyeok ;
Cho, Young Whan ;
Yoon, Kyung Byung .
JOURNAL OF ALLOYS AND COMPOUNDS, 2006, 422 (1-2) :283-287