Evaluation of mechanical properties using shear-punch testing

被引:236
作者
Guduru, RK [1 ]
Darling, KA
Kishore, R
Scattergood, RO
Koch, CC
Murty, KL
机构
[1] NC State Univ, Dept Mat Sci & Engn, Raleigh, NC 27606 USA
[2] BARC, Div Mat Sci, Bombay 400085, Maharashtra, India
来源
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2005年 / 395卷 / 1-2期
基金
美国国家科学基金会;
关键词
shear-punch test; mechanical properties; yield strengths specimen thickness; die-punch clearance;
D O I
10.1016/j.msea.2004.12.048
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
The evaluation of mechanical properties like yield and ultimate tensile strengths from shear-punch tests is important when the availability of material is limited. A shear-punch test setup was built in our laboratory and the mechanical properties for different materials mild steel, pure Al. Zn, brass (Cu-30% Zn by wt.), Al 6061, Austenitic and Martensitic stainless steels were evaluated. A new method using 1% offset criterion in conjunction with normalized shear-punch curves was used to measure the shear yield strength. A linear Correlation between the shear data and tensile data was established for yield and ultimate strengths. The variation of the yield and ultimate shear strength was studied as a function of the sample thickness and die-punch clearance for soft, medium and high strength materials. (c) 2005 Elsevier B.V. All rights reserved.
引用
收藏
页码:307 / 314
页数:8
相关论文
共 20 条
[11]   Miniature specimen shear punch test for UHMWPE used in total joint replacements [J].
Kurtz, SM ;
Jewett, CW ;
Bergström, JS ;
Foulds, JR ;
Edidin, AA .
BIOMATERIALS, 2002, 23 (09) :1907-1919
[12]   Small punch testing for assessing the tensile strength of gradient AlNi-SiC composites [J].
León, CA ;
Drew, RAL .
MATERIALS LETTERS, 2002, 56 (05) :812-816
[13]   Mechanical properties in tension of mechanically attrited nanocrystalline iron by the use of the miniaturized disk bend test [J].
Malow, TR ;
Koch, CC .
ACTA MATERIALIA, 1998, 46 (18) :6459-6473
[14]   Compressive mechanical behavior of nanocrystalline Fe investigated with an automated ball indentation technique [J].
Malow, TR ;
Koch, CC ;
Miraglia, PQ ;
Murty, KL .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 252 (01) :36-43
[15]   Suitability of a shear punch test for dental restorative materials [J].
Nomoto, R ;
Carrick, TE ;
McCabe, JF .
DENTAL MATERIALS, 2001, 17 (05) :415-421
[16]  
SMITH DA, 1990, DESIGN HDB, P3
[17]   Shear punch tests performed using a new low compliance test fixture [J].
Toloczko, MB ;
Kurtz, RJ ;
Hasegawa, A ;
Abe, K .
JOURNAL OF NUCLEAR MATERIALS, 2002, 307 (2 SUPPL.) :1619-1623
[18]   The effect of specimen thickness and grainsize on mechanical properties obtained from the shear punch test [J].
Toloczko, MB ;
Yokokura, Y ;
Abe, K ;
Hamilton, ML ;
Garner, FA ;
Kurtz, RJ .
SMALL SPECIMEN TEST TECHNIQUES: FOURTH VOLUME, 2002, 1418 :371-379
[19]   Ductility correlations between shear punch and uniaxial tensile test data [J].
Toloczko, MB ;
Hamilton, ML ;
Lucas, GE .
JOURNAL OF NUCLEAR MATERIALS, 2000, 283 :987-991
[20]  
TOLOCZKO MB, 2001, ASTM STP, V1418, P23